一级黄色片在线自慰免费看|免费国产一级A片在线观看|国产一级A片无码免费下载

<td id="ieegi"><option id="ieegi"></option></td><td id="ieegi"><noscript id="ieegi"></noscript></td><td id="ieegi"><option id="ieegi"></option></td>
  • <table id="ieegi"><noscript id="ieegi"></noscript></table><noscript id="ieegi"></noscript>
    <noscript id="ieegi"><noscript id="ieegi"></noscript></noscript>
  • <noscript id="ieegi"><source id="ieegi"></source></noscript>
  • 廊坊互科機械裝備有限公司HUKEJIXIE
    全國咨詢熱線:15097644333
    熱門關鍵詞:
    當前位置:首頁 > 產品中心 > 水泥發泡保溫板生產線 >

    水泥發泡保溫板生產線

    咨詢熱線

    15097644333

    自保溫砌塊/勻質自保溫砌塊生產線

    建筑節能與結構一體化技術是集建筑保溫功能與墻體圍護功能于一體,墻體不需要另行采取保溫措施即可滿足現行建筑節能標準要求,實現保溫...

    全國熱線
    15097644333
    詳細信息

        建筑節能與結構一體化技術是集建筑保溫功能與墻體圍護功能于一體,墻體不需要另行采取保溫措施即可滿足現行建筑節能標準要求,實現保溫與墻體同等壽命的新型保溫體系。推廣應用一體化技術是對傳統建筑設計和施工的一次重大改革,是從根本上解決保溫工程質量安全和防火問題的有效途徑之一。
        因此,從國家住建部、消防總局以及到各省市都在實行一套切實可行的政策及措施,加快實施“建筑節能與結構一體化技術”應用推廣,保證建筑物與外墻保溫同等壽命,同時徹底解決了目前因二次保溫工程存在的材料不合格,以劣充優、偷工減料、施工不規范,導致造成墻面透水、空鼓、開裂、脫落等嚴重質量問題!

    The integrated technology of building energy conservation and structure is a new type of insulation system that integrates building insulation and wall enclosure functions. The wall does not require additional insulation measures to meet the current requirements of building energy conservation standards, achieving the same lifespan as the insulation and wall. The promotion and application of integrated technology is a major reform of traditional architectural design and construction, and is one of the effective ways to fundamentally solve the quality, safety, and fire prevention problems of insulation engineering. Therefore, a set of practical and feasible policies and measures are being implemented from the Ministry of Housing and Urban Rural Development, the State Administration of Fire Protection, and various provinces and cities, accelerating the application and promotion of "building energy conservation and structural integration technology" to ensure that buildings and exterior wall insulation have the same lifespan. At the same time, the problem of substandard materials in secondary insulation engineering, such as inferior filling, cutting corners, and non-standard construction, has been thoroughly solved, which has caused wall permeability, hollowing, cracking Serious quality issues such as detachment!


    產品的性能與優勢 Product performance and advantages

        依據國家及山東省建設部門的標準要求,( 建筑節能要求65% ---75% )又根據當地可利用材料,進行材料分析,選用水泥、礦粉、粉煤灰、尾礦砂、聚苯顆粒、爐渣、電石渣、微發泡等為主要材料,并科學添加相應的外加劑,進行混合攪拌發泡。同時,提高產品的強度,降低吸水率,并加速凝固,縮短了拆模的時間(養護溫度50℃至60℃), 8---10小時即可脫模,產品即達2.5Mpa以上。
        該產品經建筑工程質量監督檢驗測試中心檢測,按節能技術標準要求,各項指標全部合格。該產品質量輕,砌塊容重620kg(發泡混凝土容重600kg-850kg),抗壓強度≥3.5MPa-5.5MPa,吸水率≤12%(省標15%),熱阻值2.478m2·k/W (省標1.80 m2·k/w),節能可達到75%標準。該產品熱工性能好,自身結構好,無冷熱橋,施工方便,與普通加氣塊施工方法相同(無特除要求),砌筑時用砌筑砂漿薄灰砌筑(或普通砂漿)。該產品與現澆復合保溫模板同時設計、施工使用,即達到了“節能與結構一體化技術”墻體工程的標準要求。

    According to the national and Shandong Provincial Construction Department's standard requirements (building energy efficiency requirements of 65% -75%), and based on local available materials, material analysis is conducted. Cement, mineral powder, fly ash, tailings sand, polystyrene particles, slag, carbide slag, micro foaming, etc. are selected as the main materials, and corresponding admixtures are scientifically added for mixing, stirring, and foaming. At the same time, it improves the strength of the product, reduces water absorption, and accelerates solidification, shortening the time for mold removal (curing temperature from 50 ℃ to 60 ℃). The mold can be removed within 8-10 hours, and the product can reach over 2.5Mpa.
      This product has been tested by the Construction Engineering Quality Supervision, Inspection and Testing Center, and meets the requirements of energy-saving technical standards. All indicators are qualified. This product is light in weight, with a unit weight of 620kg for building blocks (600kg-850kg for foam concrete), a compressive strength of ≥ 3.5MPa -5.5MPa, a water absorption rate of ≤ 12% (provincial standard of 15%), a thermal resistance value of 2.478m2 · k/W (provincial standard of 1.80 m2 · k/w), and an energy saving standard of 75%.    This product has good thermal performance, good self structure, no cold and hot bridges, convenient construction, and the same construction method as ordinary aerated blocks (without special requirements). When masonry, thin mortar masonry (or ordinary mortar) is used. This product is designed and constructed simultaneously with the cast-in-place composite insulation template, which meets the standard requirements of "energy-saving and structural integration technology" wall engineering.

    <td id="ieegi"><option id="ieegi"></option></td><td id="ieegi"><noscript id="ieegi"></noscript></td><td id="ieegi"><option id="ieegi"></option></td>
  • <table id="ieegi"><noscript id="ieegi"></noscript></table><noscript id="ieegi"></noscript>
    <noscript id="ieegi"><noscript id="ieegi"></noscript></noscript>
  • <noscript id="ieegi"><source id="ieegi"></source></noscript>